Matériel

Retour aux types de matériel

Voici le matériel de type "2.8- divers capteurs" actuellement disponible au Téléfab :

  • Current Sensor - 30A (Non-Invasive)

    This non-invasive current sensor (also known as a “split core current transformer”) can be clamped around the supply line of an electrical load to tell you how much current is passing through it. It does this by acting as an inductor and responding to the magnetic field around a current-carrying conductor. By reading the amount of current being produced by the coil, you can calculate how much current is passing through the conductor. This particular current sensor will measure a load up to 30 Amps which makes it great for building your own energy monitor to keep your power usage down, or even building an over-current protection device for an AC load. This sensor does not have a load resistor built in, so in most cases it will be necessary to place a resistor across the output to convert the coil’s induced current to a very small measurable voltage.

    Emplacement : Armoire A3, Tiroir "Composants + Consommable"

    Constructeur : SparkFun

    Référence : SEN-11005

    Quantité : 1 (disponible : 1)

  • Bouton poussoir

    Petit bouton poussoir

    Emplacement : Armoire A3, Tiroir "Composants Electroniques"

    Quantité : 1000 (disponible : 995)

  • Bouton poussoir Grove

    Bouton pressoir avec connectique GROVE Grove - Button is a momentary push button. It contains one independent "momentary on/off" button. “Momentary” means that the button rebounds on its own after it is released. The button outputs a HIGH signal when pressed, and LOW when released. The Sig marked on silk layer stands for signal while NC stands for not used at all. There are two versions of this button available as showed in the pictures. The only difference is the direction of the Grove socket.

    Emplacement : A3 - Tiroir Composants Electroniques

    Constructeur : SeedStudio

    Quantité : 1 (disponible : 1)

  • Capteur de flux [liquide]

    +2 dans kit arrosage

    Emplacement : A3 Servante – Divers

    Quantité : 1 (disponible : 1)

  • Capteur Hall - Capteur de mesure de consommation de courant

    capteur permettant de mesurer l'intensité d'un courant électrique This is a breakout board for the fully integrated Hall Effect based linear ACS712 current sensor. The sensor gives precise current measurement for both AC and DC signals. Thick copper conductor and signal traces allows for survival of the device up to 5 times overcurrent conditions. The ACS712 outputs an analog voltage output signal that varies linearly with sensed current. The device requires 5VDC for VCC and a couple of filter capacitors.

    Emplacement : armoire A3, servante, tiroir "HALL/RTC"

    Constructeur : SparkFun

    Référence : ACS712

    Quantité : 6 (disponible : 6)

  • Clavier numérique (4x3)

    Emplacement : A3 Tiroir « Arduino »

    Quantité : 5 (disponible : 5)

  • Encodeur 24 détentes 24 impulsions

    Avec boutons montés

    Emplacement : Armoire A3, Tiroir "Composants Electroniques"

    Constructeur : Bourns

    Référence : PEC12-4220F-S0024

    Datasheet : Télécharger

    Quantité : 8 (disponible : 8)

  • Encodeurs rotatif à LED bleue

    Emplacement : Armoire A3, Tiroir "Composants Electroniques"

    Constructeur : TE Connectivity

    Référence : DPL12V2424A24KB

    Datasheet : Télécharger

    Quantité : 9 (disponible : 9)

  • ESP Eye Dev Kit

    ESP-EYE , une carte de développement pour la reconnaissance d'image et la reconnaissance vocale, intégré sur une carte ESP32, une caméra 2 megapixel camera, et un microphone numérique.

    Emplacement : A3 - Boite M5 Stack

    Constructeur : DFRobot

    Référence : DFR 0620

    Quantité : 1 (disponible : 1)

  • Hall Sensor -Grove -

    http://www.seeedstudio.com/wiki/Grove_-_Hall_Sensor The Hall Sensor measures the Hall Effect, which is a production of a voltage difference across an electrical conductor, transverse to an electric current in the conductor as well as a magnetic field perpendicular to the current. The output of the continuous-time switch Hall sensor on this Twig switches low and turns on when a magnetic field (south polarity) perpendicular to the Hall sensor exceeds the BOP threshold, and it switches high and turn on when the magnetic field disappears. Features Grove compatible interface 400ns transition period for rise and fall. Continuous-time hall effect sensor Application Ideas RPM meter. Simple dc motor. Mechanic Dimensions 20mm by 24mm For all Grove users (especially beginners), we provide you guidance PDF documents.

    Constructeur : SeedStudio

    Référence : SKU: SEN14034P

    Quantité : 1 (disponible : 1)

  • Module à effet Hall ST014

    Ce module didactique à effet Hall basé sur le capteur SS49E permet la détection d'un champ magnétique à proximité du détecteur (un aimant par exemple). Ce module didactique à effet Hall basé sur le capteur SS49E permet la détection d'un champ magnétique à proximité du détecteur (un aimant par exemple). Un potentiomètre de réglage permet de régler la sensibilité. Raccordement sur une entrée digitale d'une carte compatible Arduino ou compatible. Alimentation: 5 Vcc Sorties: A0, Gnd, Vcc et D0 Sensibilité réglable par potentiomètre Dimensions: 42 x 16 x 16 mm

    Emplacement : A3 - servante capteurs

    Quantité : 2 (disponible : 2)

  • Potentiomètre

    Emplacement : Armoire A3, Tiroir "Composants Electroniques"

    Constructeur : Bourns

    Référence : 3310Y-001-202L

    Datasheet : Télécharger

    Quantité : 12 (disponible : 12)

  • Potentiomètre - Grove -

    http://www.seeedstudio.com/depot/Grove-Rotary-Angle-SensorP-p-1242.html What does “P” mean? “P” is for “panel mount” in this product. This Grove – Rotary Angle Sensor is a sister version of original Grove – Rotary Angle Sensor. They are identical except the Grove connecter is moved to the back so that you can easily use it as a neat and wire-free human interface device. Github - Grove_Rotary_Angle_Sensor https://github.com/Seeed-Studio/Grove_Rotary_Angle_Sensor

    Emplacement : Armoire A3, Tiroir "Composants Electroniques"

    Constructeur : SeedStudio

    Référence : Rotary Angle Sensor(P)

    Quantité : 17 (disponible : 17)

  • Potentiomètre d’ajustage

    Emplacement : A3 Tiroir « Composants Electroniques » / A3 Tiroir « Reserve »

    Quantité : 37 (disponible : 37)

  • Potentiomètre Glissière - Sliding Grove

    Slider The Grove - Slide Potentiometer module incorporates a linear variable resistor with a maximum resistance of 10KΩ. When you move the slider from one side to the other, its output voltage will range from 0 V to the Vcc you apply. It connects to the other Grove modules through a standard 4-Pin Grove Cable. Three of the pins are connected to OUT (Pin 1), Vcc (Pin 3) and GND (Pin 4), while the fourth pin (Pin 2) is connected to a on-board green indicator LED. The LED is used to visually represent the resistance change on the potentiometer.

    Emplacement : A3 - Tiroir Composants Electroniques

    Constructeur : SeedStudio

    Quantité : 2 (disponible : 1)

  • Real Time Clock module (RTC)

    Module permettant la gestion du temps à l'aide d'un quartz

    Emplacement : armoire A3, servante, tiroir "HALL/RTC"

    Constructeur : SparkFun

    Référence : DS1307

    Quantité : 2 (disponible : 2)

  • RTC (circuit intégré)

    Circuit 8 pins permettant la gestion du temps réel (nécessite en plus un quartz) DS1307 Maxim DS1307+, Real Time Clock (RTC), 56B RAM Serial-I2C, 8-Pin PDIP

    Emplacement : armoire A3, servante, tiroir "HALL/RTC"

    Référence : DS1307

    Datasheet : Télécharger

    Quantité : 10 (disponible : 10)

  • RTC Real-Time Clock -Grove -

    http://www.seeedstudio.com/depot/Grove-RTC-p-758.html The RTC module is a member of Twig. It is based on the clock chip DS1307 which supports the I2C protocol. It uses a Lithium cell battery (CR1225). The clock/calendar provides seconds, minutes, hours, day, date,month, and year information. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM indicator. Note: Battery is not included. Features Real-Time Clock (RTC) counts seconds,minutes, hours, date of the month, month,day of the week, and year with Leap-Year compensation valid up to 2100 56-Byte, Battery-Backed, Nonvolatile (NV)RAM for data storage I2C serial interface 5V DC supply Programmable Square-Wave output signal Automatic Power-Fail detect and switch circuitry Consumes less than 500nA in Battery-Backup Mode with Oscillator Running For all Grove users (especially beginners), we provide you guidance PDF documents.

    Constructeur : SeedStudio

    Référence : SKU: SEN12671P

    Datasheet : Télécharger

    Quantité : 1 (disponible : 1)

  • Thermocouple Type-K Glass Braid Insulated

    36" high temperature Type-K Thermocouple with glass braid insulation.

    Constructeur : SparkFun

    Référence : SEN-00251

    Quantité : 2 (disponible : 2)

Retour aux types de matériel