Matériel

Retour aux types de matériel

Voici le matériel de type "4.1- Communications sans fils" actuellement disponible au Téléfab :

  • Antenne GPS 3V Magnetic Mount SMA

    Antenne GPS Magnet mount antenna for GPS modules operating at 3V. Designed for use with automobiles - the magnet will hold the antenna in place at speeds greater than 100mph. 5 meter cable terminated with standard male SMA connector. ANT-555

    Emplacement : A3 - Servante "Divers"

    Constructeur : SparkFun

    Référence : GPS-00464

    Quantité : 2 (disponible : 2)

  • Antenne Wifi

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Quantité : 2 (disponible : 2)

  • Arduino BlueFruit

    arduino nano avec module bluetooth intégré

    Emplacement : armoire A3, boîte "ARDUINO - RESEAUX SANS FIL"

    Constructeur : Adafruit

    Quantité : 6 (disponible : 6)

  • Arduino Bluetooth

    Emplacement : A3, Boite «  Arduino – Réseaux Sans Fil »

    Constructeur : Arduino

    Référence : BT-V06

    Quantité : 1 (disponible : 1)

  • Arduino Bluetooth V06 (BT-V06)

    Arduino Uno Avec module bluetooth intégré

    Emplacement : armoire A3, boîte "ARDUINO - RESEAUX SANS FIL"

    Constructeur : Arduino

    Quantité : 1 (disponible : 1)

  • Audio Jack Modem for iPhone and Android

    With this board, data communication between Arduino and iPhone become possible . The communication speed is 1225bps (※ The actual data transfer rate slightly lower.) It is suitable for a small amount of data communication like switch inputs and sensor information. This is a semi-finished product. In most cases, you want to solder the audio jack on the board. The audio jack is included in this kit but not pre-soldered. Also, you may need a pin header or a pin socket to this board. But neither pin header nor pin socket is included, so you have to prepare it by yourself. Dimensions: 33 x 18mm ( without audio jack )

    Emplacement : A3 - Servante "SON"

    Constructeur : Switch Science

    Référence : ARMS22-SOTFMODEM

    Quantité : 1 (disponible : 1)

  • Carte ESP8266 (Wifi) avec port série. Wifi Z - Node MCU CH340

    Emplacement : A3 Boite «  Arduino – Réseaux Sans Fil »

    Référence : ESP8266

    Quantité : 2 (disponible : 0)

  • Carte MiFare 4K

    Carte RFID 4K

    Constructeur : RF Solutions

    Référence : CARD-MIFARE4K

    Datasheet : Télécharger

    Quantité : 4 (disponible : 4)

  • Carte Weemos LoLin new Node MCU v3 (avec ESP8266Wifi)

    Emplacement : A3 Boite «  Arduino – Réseaux Sans Fil »

    Quantité : 2 (disponible : 1)

  • Carte Wifi ESP32

    Module NodeMCU ESP32 WiFi + Bluetooth Module basé sur un ESP32 cadencé à 240 MHz et exécutant le firmware open source NodeMCU. Cette carte se programme via l'IDE Arduino et est compatible avec les scripts LUA.

    Emplacement : A3 - boite Communication sans fil

    Quantité : 1 (disponible : 1)

  • Clé USB Xbee

    Emplacement : A3, Tiroir Arduino

    Constructeur : Digi International

    Référence : XU-Z11

    Datasheet : Télécharger

    Quantité : 1 (disponible : 1)

  • Émetteur/récepteur Bluetooth HC-05

    Ce module Bluetooth HC05 permet d'ajouter une liaison Bluetooth sur vos projets à microcontrôleur (communication via série TTL).

    Emplacement : A3 - boite Communication sans fil

    Quantité : 48 (disponible : 44)

  • Kit antenne pour LoRa et Sigfox

    Kit antenne LoRa et Sigfox pour module Pycom SiPy et LoPy. Antenne articulée (jusqu'à 90°) à connecteur RP-SMA mâle livré avec adaptateur UFL. Remarques : - en cas d'utilisation avec un boîtier étanche, utilisez l'adaptateur UFL 35382 - cette antenne ne convient que pour une utilisation dans les bandes LoRa 868 MHz / 915 MHz, et n'est pas compatible avec les bandes 433 MHz (du LoPy4 par exemple). Connecteurs: - RP-SMA pour l'antenne - UFL pour l'adaptateur ​Dimensions de l'antenne: Ø13 x 195 mm

    Emplacement : A3 - boite LoPy LoRawan

    Quantité : 3 (disponible : 2)

  • LoRa Radio Grove

    Grove is a very powerful platform developed by Seeed Studio to simplify your IoT projects.We have integrated the grove connector to most boards produced by Seeed to make them become a system. This time, we combined Grove with LoRa to provide an ultra-long-range wireless module for you. The main functional module in Grove - LoRa Radio 433MHz is RFM98, which is a transceiver features the LoRa long range modem that provides ultra-long range spread spectrum communication and high interference immunity whilst mini-missing current consumption. The heart of Grove - LoRa Radio 433MHz is ATmega168, a widely used chip with very high-performance and low power consumption, especially suitable for this grove module. There we already integrated a simple wire antenna to receive signal, if the signal is too weak to receive, don’t worry, the MHF connector next to the antenna is for adding a second antenna which has MHF interface to gain more signal. This is the 433MHz version, which can be used for 433MHz communication. You can also find the version for 868MHz at Grove - LoRa Radio 868MHz.

    Emplacement : A3 - Boite Réseaux Sans Fil

    Constructeur : SeedStudio

    Quantité : 14 (disponible : 12)

  • Module bluetooth "Blue SMiRF" Silver

    Module compatible Arduino permettant de communiquer via une connexion bluetooth, basé sur le module RN-42.

    Emplacement : A3, Boite «  Arduino – Réseaux Sans Fil »

    Constructeur : SparkFun

    Quantité : 13 (disponible : 13)

  • Module Bluetooth CMS

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Constructeur : Hope RF

    Référence : RFM70-S

    Datasheet : Télécharger

    Quantité : 4 (disponible : 4)

  • Module Bluetooth Modem - BlueSMiRF HID

    The BlueSMiRF HID is essentially the same board as the BlueSMiRF Silver but the populated RN-42 comes loaded with the HID firmware. HID, or “Human Interface Device,” is the communication protocol used for computer peripherals such as keyboards, mice and joysticks. This makes the RN-42-HID a simple and powerful tool for creating wireless peripheral devices which can be universally recognized and used without the installation of special drivers. The manual included in the documentation below goes into more detail about the Bluetooth HID profile. The remote unit can be powered from 3.3V up to 6V for easy battery attachment. All signal pins on the remote unit are 3V-6V tolerant. No level shifting is required. Do not attach this device directly to a serial port. You will need an RS232 to TTL converter circuit if you need to attach this to a computer.

    Constructeur : SparkFun

    Référence : WRL-10938

    Quantité : 2 (disponible : 2)

  • Module Bluetooth v2.0 Serial Transceiver

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Quantité : 7 (disponible : 7)

  • Module Récepteur RFID MiFARE

    Emplacement : A3, Tiroir Arduino

    Constructeur : RF Solutions

    Référence : RWD-MIFARE

    Datasheet : Télécharger

    Quantité : 1 (disponible : 1)

  • Module RFID + Tag

    Le module RFID-RC522 est une carte d'interface compatible Arduino et Raspberry Pi, basée sur le circuit MFRC-522 de NXP et est utilisée pour lire et écrire sur des cartes ou badges RFID de type Mifare.

    Emplacement : Projet FPA

    Référence : RC522

    Quantité : 30 (disponible : 30)

  • Module WiFi ESP8266

    WiFi-Serial-Transceiver-Module-Breakout-Board

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Référence : ESP8266

    Quantité : 9 (disponible : 9)

  • Module wifi ESP8266 Joy-IT

    Le module WiFi basé sur l’ESP8266 est compatible avec n’importe quelle plate-forme Open Source, comme par ex. Raspberry, Arduino, BananaPI et Cubiebioard

    Emplacement : A3, Boite « Arduino – Réseaux Sans Fil

    Constructeur : Joy-It

    Référence : Module wifi ESP8266 Joy-IT

    Datasheet : Télécharger

    Quantité : 2 (disponible : 2)

  • Module WiFi serial transciever - ESP8266

    Module Wi-Fi https://www.seeedstudio.com/WiFi-Serial-Transceiver-Module-w-ESP8266-1MB-Flash-p-2485.html http://wiki.seeedstudio.com/WiFi_Serial_Transceiver_Module/

    Emplacement : A3, Boite «  Arduino – Réseaux Sans Fil »

    Constructeur : SeedStudio

    Référence : SKU 317060016

    Quantité : 3 (disponible : 1)

  • Module XBee

    Modules compatibles arduino permettant la communication entre de board distantes. 3 modèles disponibles : Xbee S1, Xbee S2 et Bluetooth Bee

    Emplacement : armoire A3, boîte "XBEE"

    Quantité : 17 (disponible : 17)

  • Recepteur

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Référence : WRL10532

    Quantité : 1 (disponible : 1)

  • RF Link Receiver - 4800bps (434MHz)

    hese wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only receivers, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair. Note: These modules are indiscriminate and will receive a fair amount of noise. Both the transmitter and receiver work at common frequencies and don’t have IDs. Therefore, a method of filtering this noise and pairing transmitter and receiver will be necessary. The example code below shows such an example for basic operation. Please refer to the example code and links below for ways to accomplish a robust wireless data link.

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Constructeur : SparkFun

    Référence : WRL-10532

    Quantité : 3 (disponible : 3)

  • RF link Transmitter 434Mhz

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Constructeur : SparkFun

    Référence : WRL-10534

    Quantité : 3 (disponible : 3)

  • RN-XV WiFly Module - Wire Antenna

    The RN-XV module by Roving Networks is a certified Wi-Fi solution especially designed for customer who want to migrate their existing 802.15.4 architecture to a standard TCP/IP based platform without having to redesign their existing hardware. In other words, if your project is set up for XBee and you want to move it to a standard WiFi network, you can drop this in the same socket without any other new hardware. The RN-XV module is based upon Roving Networks' robust RN-171 Wi-Fi module and incorporates 802.11 b/g radio, 32 bit processor, TCP/IP stack, real-time clock, crypto accelerator, power management unit and analog sensor interface.The module is pre-loaded with Roving firmware to simplify integration and minimize development time of your application. In the simplest configuration, the hardware only requires four connections (PWR, TX, RX and GND) to create a wireless data connection.

    Emplacement : A3, Tiroir Arduino

    Constructeur : SparkFun

    Référence : WRL-10822

    Quantité : 1 (disponible : 1)

  • Shield arduino (grand) et support (petit) Xbee

    -- SHIELD compatible arduino permettant de faire communiquer l'arduino et le XBee sur le port série. -- SUPPORT Permettant de gérer un module XBee

    Emplacement : armoire A3, boîte "XBEE"

    Quantité : 13 (disponible : 13)

  • Transmetteur

    Emplacement : A3 - Servante "TELECOM SANS FIL"

    Référence : WRL10534

    Quantité : 1 (disponible : 1)

  • Xbee Explorer Dongle

    Support pour module RF, connectable par USB

    Emplacement : Armoire A2

    Constructeur : SparkFun

    Référence : WRL-09819

    Quantité : 1 (disponible : 1)

  • XtremeBee v12

    Emplacement : A3 Boite « XBee »

    Quantité : 1 (disponible : 1)

Retour aux types de matériel