Voici le matériel de type "2.2- capteurs metéo (t°, humidité, pression...)" actuellement disponible au Téléfab :
-
Altitude/Pressure Sensor Breakout - MPL3115A2
Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it’s easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius. This breakout board makes it easy to prototype using this tiny device by breaking out the necessary pins to a standard 0.1" spaced header. The board also has all of the passive components needed to get the device functioning, so you can simply connect it to something that talks I2C and get to work!
Emplacement : A3, petit tirroir
Constructeur : SparkFun
Référence : SEN-11084
Plus d'infos : https://www.sparkfun.com/products/11084
Quantité : 2 (disponible : 2)
-
Capteur de pression barométrique BMP085
Emplacement : A3 - Servante "METEO"
Constructeur : SparkFun
Référence : SEN-09694
Datasheet : Télécharger
Plus d'infos : https://www.sparkfun.com/products/9694
Quantité : 1 (disponible : 1)
-
Capteur de pression, d'humidité et de T° BME280
Ce capteur est basé sur le circuit BME280 et mesure la température, l'humidité et la pression atmosphérique. Il communique avec un microcontrôleur type Arduino ou compatible via le bus I2C ou SPI. Ce module se raccorde au microcontrôleur via un connecteur 6 broches mâles au pas de 2,54 mm. Caractéristiques: Alimentation: 3,3 Vcc Plages de mesure: - température: -40 °C à 85 °C - humidité: 0 à 100% HR - pression: 30 à 110 kPa - altitude: en fonction de la pression Précision: - température: ±1 °C - humidité: ±3 % - pression: ±1 hPa Dimensions: 15 x 12 mm Interfaces: I2C et SPI
Emplacement : A3 - servante capteurs Meteo
Constructeur : Velleman
Plus d'infos : https://www.velleman.eu/downloads/29/vma335_a4v01.pdf
Quantité : 1 (disponible : 1)
-
Capteur de température DS18B20 1-Wire
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor.
Emplacement : A3 - Servante "METEO"
Constructeur : Maxim
Référence : DS18B20
Datasheet : Télécharger
Quantité : 8 (disponible : 8)
-
Capteur de température LM335Z
Le LM335Z est un capteur analogique, pour apprendre à l'utiliser, vous pouvez rendre une petite visite au site suivant http://www.pobot.org/Capteur-de-temperature-analogique.html
Emplacement : A3 - Servante "METEO"
Constructeur : STMicroelectronics
Référence : LM335Z
Datasheet : Télécharger
Quantité : 20 (disponible : 20)
-
Capteur Grove Niveau d'eau - Water sensor
Grove Water sensor The Water Sensor module is part of the Grove system. It indicates whether the sensor is dry, damp or completely immersed in water by measuring conductivity. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins to detect the amount of water induced contact between the grounded and sensor traces.
Emplacement : A3 - Servante "METEO"
Constructeur : SeedStudio
Quantité : 2 (disponible : 2)
-
Capteur Humidité Température DHT-11
3 capteurs Grove 3 à connecter
Emplacement : A3 servante capteur Meteo
Référence : DHT11
Quantité : 20 (disponible : 19)
-
Capteur Humidité Température DHT-22
https://www.sparkfun.com/products/10167 The RHT03 (also known by DHT-22) is a low cost humidity and temperature sensor with a single wire digital interface. The sensor is calibrated and doesn't require extra components so you can get right to measuring relative humidity and temperature.
Emplacement : A3 servante Meteo
Constructeur : SparkFun
Plus d'infos : https://github.com/sparkfun/RHT03
Quantité : 3 (disponible : 3)
-
Capteur Pression + Température + Altitude BMP280
apteur basé sur un circuit BMP280 permettant la mesure de la pression atmosphérique, de la température et de l'altitude. Ce module communique avec une carte type Arduino (ou compatible) ou Raspberry Pi via une interface I2C. Ce module est livré sans cordon. Il est recommandé d'utiliser un jeu de cordons M/F de type BBJ21. Un guide d'utilisation pour Arduino et Raspberry Pi est disponible en fiche technique. Caractéristiques: Alimentation: 3,3 à 5 Vcc Plages de mesure: - température: -40 °C à 85 °C - pression: 30 à 110 kPa - altitude: en fonction de la pression Précision: - température: ±1 °C - pression: ±1 hPa - altitude: ±1 m Interface: I2C Référence Joy-It: SEN-KY052
Emplacement : A3 Servante – METEO
Constructeur : Joy-It
Référence : SEN-KY052
Datasheet : Télécharger
Plus d'infos : https://www.gotronic.fr/art-module-bmp280-ky052-29155.htm
Quantité : 4 (disponible : 4)
-
Capteur Température Humidité Grove SHT31
Grove - Temp&Humi Sensor(SHT31) is a highly reliable, accurate, quick response and integrated temperature & humidity sensor. The sensor(chip) used in the module is designed with Sensirion's CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module can be ±2%RH (for relative humidity) and ±0.3°C (for temperature). This module is compatible with 3.3 Volts and 5 Volts and hence does not require a voltage level shifter. This module communicates using with I2C serial bus and can work up to 1 MHz speed. We also have provided a highly abstracted library to make this product more easier to use. Using the sensor is easy. For Seeeduino (compliant with Arduino), just connect this breakout board with the main control board via Grove cable. Then use the provided library and example/demo code available at GitHub to get your data. If you're using an Arduino without a Base Shield, simply connect the VIN pin to the 5V voltage pin, GND to ground, SCL to I2C Clock (Analog 5) and SDA to I2C Data (Analog 4).
Emplacement : A3 - Servante Météo
Constructeur : SeedStudio
Référence : SHT31
Plus d'infos : http://wiki.seeedstudio.com/Grove-TempAndHumi_Sensor-SHT31/
Quantité : 1 (disponible : 1)
-
Humidité
HIH-4030 Breakout https://www.sparkfutelefan.com/products/9569
Emplacement : A3 - Servante "METEO"
Constructeur : SparkFun
Référence : SEN-09569
Datasheet : Télécharger
Plus d'infos : http://bildr.org/2012/11/hih4030-arduino/
Quantité : 1 (disponible : 1)
-
Humidité de terre
+2 Kit arrosage
Emplacement : A3 Servante – METEO
Quantité : 7 (disponible : 7)
-
Humidité et Température Si7021
Emplacement : A3 Servante – METEO
Référence : Si7021
Quantité : 1 (disponible : 1)
-
Infrared Temperature Breakout - TMP006
This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emitting, the TMP006 Breakout can determine how hot or cold the object is. The TMP006 Breakout has a wide temperature detection range of -40°C to 125°C and an optimal operating voltage of 3.3V to 5V (tolerant up to 7V max). This breakout works great with most micro controllers connecting via the I2C bus.
Constructeur : SparkFun
Référence : SEN-11859
Plus d'infos : https://www.sparkfun.com/products/11859
Quantité : 1 (disponible : 1)
-
Pluie
Emplacement : A3 Servante – METEO
Quantité : 1 (disponible : 1)
-
Température
Emplacement : A3 Servante – METEO
Référence : LM75 (Rasperry Pi)
Quantité : 1 (disponible : 1)
-
Thermomètre infrarouge
https://www.sparkfun.com/products/9570 Melexis' MLX90614ESF-BAA is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614's high accuracy and resolution. It has a huge number of applications including body temperature measurment and movement detection. The MLX90614 provides two methods of output: PWM and SMBus (i.e. TWI, I2C). The 10-bit PWM output provides a resolution of 0.14°C, while the TWI interface has a resolution of 0.02°C. The MLX90614 is factory calibrated in wide temperature ranges: -40 to 85°C for the ambient temperature and -70 to 382.2°C for the object temperature. The measured value is the average temperature of all objects in the Field Of View of the sensor. The MLX90614 offers a standard accuracy of 0.5°C around room temperatures. This devices comes in an industry standard TO-39 package. We're carrying the 3V version of this sensor.
Emplacement : A3 - Servante "METEO"
Constructeur : SparkFun
Référence : SEN-09570
Datasheet : Télécharger
Plus d'infos : http://bildr.org/2011/02/mlx90614-arduino/
Quantité : 1 (disponible : 1)